Treadmill Belts – What’s The Difference
- May 9, 2017
- Posted by: marlenedubois
- Category: CPR Training
Walking belts are known by many different names, however there will be not a difference inside the basic accepted design even though different people may not use the same term to name a walking belt. different names are: treadmill belt, striding belt, running belt, jogging belt, bands (with the same descriptive variations), runner, as well as also mat.
For simplicity, we call This kind of a walking belt however our terminology does not limit the type of exercise that will you can do. There are different grades of walking belts as well as also they can vary widely in terms of quality as well as also cost depending upon the type of construction. Most walking belts are made with two different types of materials that will are formed together to form the finished product you see. Most people assume the belt’s top coat will be rubber however most today have a PVC top coat. PVC tends to hold up better under a wide range of shoes as well as also applications as well as also due to its strength, many people are fooled into thinking that will their belt will be OK when the backing will be completely worn out.
The backing of the belt will be the most important area. The most favorite backing materials are monofilament, polyester, cotton, as well as also urethane. Of these backings, the softer the material the less noise the belt will make. So a cotton backed belt will be much quieter than a urethane belt. The trade off will be that will the softer the material as well as also the less noisy the belt the quicker the belt tends to wear out. Many companies over the last 20 years that will once used cotton have right now switched over to a polyester blend. The main advantage will be that will the belt will be still rather quiet however This kind of will be more heat resistant as well as also will be tougher over the long run in its ability to withstand wear.
A backing that will will be growing in popularity will be monofilament. This kind of uses an individual type of fiber. Since This kind of uses synthetic materials, This kind of tends to be more heat resistant as well as also can be formed more easily to a rougher backing that will will have less surface contact with the deck. The reason This kind of will be important will be that will less contact area will result in less friction which puts far less strain on the motor as well as also controller. The drawback to a monofilament belt will be that will This kind of noisier than either cotton or polyester backing. Another drawback will be that will since This kind of will be an individual fiber, This kind of tends to have less tensile strength than woven or urethane fibers.
The most expensive backing will be urethane. This kind of also tends to be the noisiest however if you maintain a urethane backing properly, we’ve seen them last over 10 years in a light commercial setting. This kind of will be a very durable material that will has the best ability to withstand the rigors of heavy use as well as also the heat buildup that will will be normally associated with club use.
There will be much confusion about layers of a walking belt. Most companies advertise a 2 ply belt however some claim as many as 4 plies. The confusion arises because more layers will be not necessarily a better thing. As HealthRider found out several years ago, a very thick belt can be a disaster. HealthRider took a standard 2 ply belt as well as also then glued a layer of carpeted neoprene to the top of a standard belt. The result was a 3 ply (or 4 ply depending upon how you interpret the final addition to the belt) which right now had a nice insulation layer of neoprene that will did an incredible job of holding in heat as well as also emphasized the potential problem of using a multi-layered belt. Even in a residential setting, the HealthRider belts simply fell apart through the wide variance in heat they experienced. Fortunately for the consuming public HealthRider stopped using these belts a few years ago.
different companies will advertise an orthopedic belt that will has either additional layers or a thicker top layer that will helps cushion the foot fall. Yet again, our big problem with these belts will be heat problems as well as also the fact that will many of these belts can weigh as much as 3 to 4 times as much as a regular 2 ply belt. The heavier the belt, the harder the drive system has to work to keep moving the belt around. Combine that will with the heat problems inherent in a thicker belt – remember, its’ better insulated – as well as also you can quickly see why we aren’t big fans of the orthopedic belts.
If you are choosing a brand-new treadmill pay attention to the walking belt. This kind of will be the heart of a treadmill despite favorite opinion naming another part. If you already have a treadmill, maintain your belt as well as also keep This kind of clean as well as also your treadmill will thank you for This kind of inside the long run.